The air purifier draws in room air through the air inlet, circulates it through a Pre-Filter, a Deodorizing Filter and a Micro HEPA Plus Filter inside the product, and then discharges it through the air outlet. The Micro HEPA Plus Filter can remove 99% of dust particles as small as 0.02 microns that pass through the filter and also helps absorb odors. (This filter also traps 99.97% of dust particles as small as 0.3 microns.) The Deodorizing Filter gradually absorbs odors as they pass through the filter. With Hepa air purifier Some odors absorbed by the filters will break down over time, causing additional odors. Depending on usage conditions, and especially if the product is used in environments significantly more severe than a normal household, these odors may become noticeable sooner than expected. If these odors persist, replace the filters.
The portable air purifier is designed to remove air-suspended dust and the odors. The Room air purifier is not designed to remove harmful gases such as carbon monoxide contained in cigarette smoke. The air purifier may not completely remove an odor if the source of the odor is still present. Sharp air purifier is best air purifier for home removes the odors as well as dust particles. Sharp hepa filter air purifier can remove 99% of dust particles. Sharp air purifier is helpful for patients suffering from Asthma, COPD & other respiratory diseases. It is advisable that air purifier for asthma patients is highly recommended. Also Sharp Air purifier for indoor pollution is highly recommended.
FEATURES
A unique Combination of Air Treatment Technologies Triple Filtration System + Plasma cluster Plasmacluster High Density Plasmacluster 25000 The higher the ion density, the greater the effect. By emitting a balance of positive and negative ions, Plasmacluster air treatment is a natural process. Triple Filtration System TRAPS DUST Pre-filter traps dust larger than approx 240 micron particles. DECREASES ODORS Deodorizing filter absorbs many common household odors. REDUCES TINY DUST, POLLEN & MOLD The Micro HEPA Plus filter traps 99% of particles as small as 0.02 microns. (traps 99.97% of particles as small as 0.3 microns.) Unique Airflow Powerful air suction and unique airflow quickly and efficiently collect dust and other particles. Faster airflow at a 20º angle causes dust to be collected at lower levels in the room for more effective cleaning. Plasmacluster can remove static electricity and can thus prevent dust from attaching to walls and other surfaces. Wi-Fi Function Confirms that the air quality of the room has become clean visually. Controls the product through smart devices such as a remote control. Proposes optimal timing for filter exchange. Trademarks “Wi-Fi® ” is a registered trademark of Wi-Fi Alliance®. “WPA™”,“WPA2™” and “WPA3™” are trademarks of Wi-Fi Alliance®. The Bluetooth® word mark is a registered trademark owned by Bluetooth SIG,. Inc. “Android™” is the trademark of Google Inc. The other company names, corporate names, product names mentioned in the handling instructions are trademarks and registered trademarks of each company.
OPERATION
START/STOP START STOP When the product starts operating the operation starts in the previous mode it was operated in. SELECT AIR VOLUME AND MODE LOW MED MAX AUTO POLLEN SLEEP AUTO: The fan speed is automatically switched depending on the amount of impurities in the air and room brightness. POLLEN: The Sensitive Dust Sensor sensitivity is automatically increased and the Sensitive Dust Sensor quickly detects impurities such as dust and pollen and cleans the air powerfully. SLEEP: The product will operate quietly, and the fan speed will automatically be switched depending on the amount of impurities in the air and room brightness. When the Light Control is set to “Auto”, the Display and Cleanliness Indicator will automatically go off
HAZE MODE Operates at HIGH fan speed for 60 minutes and then alternates between Low and High level for 20 minutes each. 10 minutes: Max High fan level 50 minutes: High fan level 20 minutes: Low fan level 20 minutes: High fan level The Plasmacluster ion cannot be turned “OFF”.
CARE AND MAINTENANCE
To maintain optimum performance of this air purifier, please clean the product including the filter periodically. Be sure to stop operation and unplug the product before any maintenance or replacing accessories
SIDE PANELS / PRE-FILTERS Remove the dust gently with a cleaning tool such as a vacuum cleaner
Do not apply excessive pressure when scrubbing the Pre-Filter.
How to Clean Hard-to-Remove Dirt.
SENSORS Remove the dust gently with a cleaning tool such as a vacuum cleaner
How to Clean Hard-to-Remove Dirt. Sensor Filter (Sensitive Dust Sensor)
MICRO HEPA PLUS FILTERS / DEODORIZING FILTERS REPLACEMENT AND MAINTENANCE CYCLE
MAINTENANCE
Remove the dust on the filters. Do not wash the filters. Do not expose to sunlight (Otherwise these filters may lose their efficacy.) MICRO HEPA PLUS FILTER Maintain and clean only the tagged surface. Do not clean the opposite surface. The filter is fragile, so be careful not to apply too much pressure. Tag DEODORIZING FILTER Both surfaces can be maintained and cleaned. The filter is fragile, so be careful not to apply too much pressure. Some odors absorbed by the filters will break down over time, causing additional odors. Depending on usage conditions, and especially if the product is used in environments significantly more severe than a normal household, these odors may become noticeable sooner than expected. Replace the filter in those cases or if dust is unable to be removed after maintenance
REPLACEMENT
Filter Replacement Indicator The Filter Replacement Indicator will start flashing to remind the filter replacement is required. The flashing speed becomes faster once the filter is requires to change immediately. Filter life varies depending on the operation mode and the room environment. Flashes slowly Flashes quickly After the filters are replaced, connect the power plug to the wall outlet and press Power ON/OFF Button, then press and hold the Filter Reset Button for 3 seconds to reset the Filter Replacement Indicator. Press for 3 sec. For directions on how to install the filter when replacing. Please consult your dealer for purchase of replacement filter. Use only the filter designed for this product. It is recommended that you note down the date when the filters were replaced for future reference
Disposal of Filters Please dispose of the replaced filter according to the local disposal laws and regulations. Micro HEPA Plus Filter materials: Polypropylene, Polyethylene Deodorizing Filter materials: Polypropylene, Polyester, Activated Carbon. Do not wash and reuse replaced filter
PLASMACLUSTER ION GENERATING UNIT (Electrode Section
REPLACEMENT AND MAINTENANCE CYCLE
MAINTENANCE
Install the Side Panel and filters at the left side of the Main Body. Do not clean with anything other than the Unit Cleaning Brush. Doing so could lead to failures in the Unit. But if the electrode’s base part is contaminated, clean it with a slightly wet cotton swab. A bent electrode could be cut off and dropped during the cleaning process, but it will not change the performance. Do not touch the electrode directly. Doing so could lead to pain/itching. Do not transform the Electrode Section. Doing so can damage it. Do not touch the Connection Terminals. Doing so can damage them.
REPLACEMENT Unit Replacement Indicator When the total operation time exceeds 17,500 hours, the Unit Replacement Indicator will flash to indicate that the Unit needs replacement
How to replace the Unit Please consult your dealer for purchase of a replacement Unit. Use only the Unit designed for this product
TROUBLESHOOTING
ABOUT THE PRODUCT Odor and smoke persist. Check the filters. If they appear to be extremely dirty, clean or replace them. Air discharged from the product has an odor. Check to see if the filters are extremely dirty. Clean or replace the filters. The product does not operate when cigarette smoke is in the air. Make sure the product is installed in a location in which the sensors can detect cigarette smoke. Check to see if the Sensitive Dust Sensor openings are blocked or clogged. If they are blocked or clogged, clean the Sensor Filter. Smell from a new product and/or filter. Immediately after removing the plastic bag, a slight odor may occur. This odor is not harmful for filter performance or to humans. The product makes a clicking or ticking sound. The product may make clicking or ticking sounds when it is generating ions. The Cleanliness Indicator is blue even when the air is not clean. The air may have been dirty when the product was plugged in. Unplug the product, wait one minute, and then plug the product in again. The Cleanliness Indicator is red even when the air is clean. Dirty or clogged Sensitive Dust Sensor openings interfere with sensor operation. Gently clean the Sensor Filter. Is the sensor part on the rear blocked by the wall? →If you feel that the response of the cleanliness indicator is slow, place the product about 3cm away from the wall.
The Cleanliness Indicator changes color frequently. The Cleanliness Indicator automatically change color when the Sensitive Dust Sensor and Sensitive Odor Sensor detect impurities. If you are concerned about the change, you can change sensor sensitivity.
Filter Replacement Indicator is on. Whenever after replacing the filters, connect the power cord to an outlet and then press the Filter Reset Button for more than 3 seconds.
The Display goes off. When the Light Control is set to “Auto”, the light automatically turns off when the room is dark or operating in sleep mode. Moreover, when the Light Control is set to “OFF”, the light is always off. If you do not want the light to be off, set the Light Control to the “Dim” setting
The Display does not match the weather report or another hygrometer or thermometer in the room. Outdoor and indoor as well as the home environment (the volume of traffic nearby, number of stories in a home, etc.) may cause a reading different than those data. There is a difference in the level within the same room.
ABOUT THE Wi-Fi FUNCTION The Wi-Fi connection of the air purifier and the router is not working. Check the specifications of the router in use. Adjust the router and antenna direction, move the router and antenna closer, and so on. After that, reswitch to turn on the router and perform the INITIAL SET UP again. The connection between the air purifier and your smart device cannot be established. Are the air purifier and your smart device connected to the same router? Connect the air purifier and your smart device to the same router. If you still can’t connect, try connecting your smart device to the 2.4GHz band or the 5GHz band of the router. Is the total number of smart devices being in use exceeding the maximum number for registration on one air purifier? The maximum number of smart devices that can be registered on one air purifier is 10. Is the total number of products (air conditioners, air purifiers, etc.) to be registered with one smart device exceeding the maximum designated number? The maximum number of products to be registered with one smart device is 30. Remote operation from a smart device cannot be performed. Is the Wi-Fi Indicator of the air purifier on? If the Wi-Fi Indicator is off, please perform “A1: Wi-Fi adapter ON/OFF” to turn on the product Wi-Fi. Has the connection between the air purifier and your smart device been completed? Set up the connection between the air purifier and your smart device. Is the Wi-Fi indicator of the air purifier blinking? If the Wi-Fi indicator is blinking, check the communication status on the Internet. After inserting the power plug of the air purifier into the outlet, it may take some time before the Wi-Fi indicator is lit. You cannot operate the product via the smart device when the Wi-Fi Indicator is not lit
